2008 Polaris Ranger XP 700 Problems: 6 Common Issues and Fixes

This post contains affiliate links. If you buy through them, we may earn a commission at no extra cost to you. Learn more

The most common 2008 Polaris Ranger XP 700 problems are EFI wiring harness faults (TBAP and crank sensor wires), backfiring and poor running until warm, power loss from low fuel pressure, AWD engaging in 2WD, starter trouble and the 2008 fuel tank seam bulletin. Most running problems on this model come from wiring rather than failed sensors.

The 2008 Ranger XP 700 is a full-size Polaris utility side-by-side with a fuel-injected 700-class twin-cylinder engine, a CVT (PVT) transmission and Polaris’ On-Demand AWD. Its age means harness wear, fuel pumps and AWD parts are now the main things to check.

2008 Ranger XP 700 Problems at a Glance

ProblemCommon symptomMost likely causeFirst fix to tryPart you may need
EFI harness faultsMisfires, backfires, rough runningChafed TBAP or crank sensor wiringInspect and repair harnessHarness repair kit
Won’t take gas until warmBogs and backfires when coldTBAP harness or sensorCheck harness, clean TBAP sensorTBAP sensor
Power loss on long ridesLoses power after hoursLow fuel pressureFuel pressure test (about 39–41 psi)Fuel pump
AWD engaging in 2WDHard steering, one front wheel drivingFront drive / AWD coil, wiringCheck wiring and front diff fluidFront drive parts
Starter troubleClicks or slow crankBattery, cables, solenoidClean cables, test batteryStarter solenoid
Fuel tank seam bulletinFuel smell or leakWeak tank seam on some 2008 unitsDealer check (bulletin R-07-08)Free tank replacement

1. EFI Wiring Harness Faults

A 2008 Ranger 700XP ran fine for 10–20 minutes, then starved for fuel, misfired, backfired and nearly quit. The voltages, spark plugs and fuel pressure (39–40 psi) all checked out, and there were no codes. Forum members pointed to the TPS/TBAP and crank sensor harness under the throttle body. The owner found two wires partly rubbed through by the frame, and responders advised repairing the harness rather than replacing sensors.

  1. Inspect the wiring under the throttle body and along the frame for chafed spots.
  2. Wiggle the harness while it runs to see whether the engine changes.
  3. Repair damaged wires with a heavy-duty harness repair kit and secure them away from the frame and starter.
  4. Protect connectors with dielectric grease.

Parts you may need: TBAP harness repair kit, connectors.

2. Won’t Take Gas Until It Warms Up

Another 2008 700XP owner said it idled at about 950–975 RPM but wouldn’t take gas and backfired until it warmed up for 5–10 minutes. The advice was to check the TBAP sensor wiring for bare or melted spots, tie the crank sensor harness away from the starter, and remove and clean the TBAP sensor. Fault codes 41, 43 and 45 can appear with TBAP harness problems.

3. Power Loss on Long Rides

One owner’s 2008 Ranger XP 700 started losing power after about 3 to 3.5 hours of riding, along with a gas smell. A gauge showed fuel pressure falling from about 38 psi cold to 32 psi when the problem began. A forum member said pressure should stay around 39–41 psi and that 32 psi would make it run poorly under load, pointing to the fuel pump.

  • Test fuel pressure with a gauge, cold and after a long ride.
  • Replace the fuel filter and check the fuel lines.
  • Replace the pump if pressure drops under load.
  • Use fuel stabilizer if the Ranger sits for weeks.

Parts you may need: fuel pump, fuel filter.

4. AWD Engaging in 2WD

A 2008 Ranger XP owner found that in 2WD the left front wheel seemed to drive, making steering hard. Suggestions included checking the wiring from the AWD switch to the front drive, looking for milky front gearcase fluid, and inspecting the front drive internals. Clean and grease the AWD connectors first, and check the front differential fluid at every service.

Parts you may need: front drive parts, AWD coil (after diagnosis).

5. Starter Trouble

Clicking or slow cranking is usually the battery or a corroded cable. Clean the terminals, test the battery and starter voltage with a digital multimeter, and keep the battery on a battery maintainer.

6. 2008 Fuel Tank Seam Bulletin

Polaris issued safety bulletin R-07-08 for some 2008 Ranger models built between August 21 and October 3, 2007, because the fuel tank seam might not be bonded properly and could leak. Dealers inspect the fuel tank date code and replace the tank free if needed. If your 2008 Ranger has a fuel smell, ask a dealer to check whether this bulletin applies to your VIN.

Maintenance That Prevents Most Ranger XP 700 Problems

How oftenWhat to do
After muddy ridesCheck harness and connectors, clean air filter, rinse radiator
MonthlyBattery test, coolant (50/50 coolant), oil, tire pressure
Per owner’s manualOil and filter, front and rear gearcase fluid, belt inspection
Before storageFresh fuel with stabilizer, battery maintainer

Frequently Asked Questions

Why does my 2008 Ranger 700 backfire?

Most often it is a chafed TBAP or crank sensor harness. Inspect the wiring under the throttle body before replacing sensors.

What fuel pressure should a Ranger 700 EFI have?

Owners and techs on forums cite about 39–41 psi, staying steady under load.

Is there a recall on the 2008 Ranger XP 700?

Polaris issued safety bulletin R-07-08 for a fuel tank seam on some 2008 Rangers built in August–October 2007. Ask a dealer to check your VIN.

Is a used 2008 Ranger XP 700 worth buying?

It can be, if the wiring harness, fuel pump, AWD and belt are in good shape and the fuel tank bulletin has been checked.

Conclusion

Wiring is the first thing to check on a 2008 Ranger XP 700, followed by fuel pressure and the AWD system. Fix the harness properly and this Ranger can keep working for years.

Related guides: 2008 Polaris RZR 800 problems · Kawasaki Mule 4010 problems · Honda Pioneer 1000 problems

Written by Faisal Abbasi

Faisal Abbasi researches and writes troubleshooting guides for UTVs, ATVs and off-road vehicles at OffroadCares. Each guide combines owner reports, service manuals and parts data into clear, step-by-step fixes, and is checked by an experienced mechanic before it goes live.

Leave a Comment